Nokia codes/functions ! HOT

SmoothCriminal

New Member
Disciple
Jan 27, 2005
74
2
0
36
www.spicesms.com
Hi guyz.. here are some Secret Codes for your Mobiles.. Dont blame me if they dont work!.. Just thought its a good resource to share..
ALL NOKIA PHONES

*3370# -This Nokia code activates Enhanced Full Rate Codec (EFR) - Your Nokia cell phone uses the best sound quality but talk time is reduced my approx. 5%

#3370# - Deactivate Enhanced Full Rate Codec (EFR)

*#4720# - Activate Half Rate Codec - Your phone uses a lower quality sound but you should gain approx 30% more Talk Time

*#4720# With this Nokia code you can deactivate the Half Rate Codec

*#0000# Displays your phones software version, 1st Line : Software Version, 2nd Line : Software Release Date, 3rd Line : Compression Type

*#9999# Phones software version if *#0000# does not work

*#06# For checking the International Mobile Equipment Identity (IMEI Number)

#pw+1234567890+1# Provider Lock Status. (use the "*" button to obtain the "p,w" and "+" symbols)

#pw+1234567890+2# Network Lock Status. (use the "*" button to obtain the "p,w" and "+" symbols)

#pw+1234567890+3# Country Lock Status. (use the "*" button to obtain the "p,w" and "+" symbols)

#pw+1234567890+4# SIM Card Lock Status. (use the "*" button to obtain the "p,w" and "+" symbols)

*#147# This lets you know who called you last (Only vodofone)

*#1471# Last call (Only vodofone)

#21# This phone code allows you to check the number that "All Calls" are diverted to

*#2640# Displays phone security code in use

*#30# Lets you see the private number

*#43# Allows you to check the "Call Waiting" status of your cell phone.

*#61# Allows you to check the number that "On No Reply" calls are diverted to

*#62# Allows you to check the number that "Divert If Unreachable (no service)" calls are diverted to

*#67# Allows you to check the number that "On Busy Calls" are diverted to

*#67705646# Phone code that removes operator logo on 3310 & 3330

*#73# Reset phone timers and game scores

*#746025625# Displays the SIM Clock status, if your phone supports this power saving feature "SIM Clock Stop Allowed", it means you will get the best standby time possible

*#7760# Manufactures code

*#7780# Restore factory settings

*#8110# Software version for the nokia 8110

*#92702689# Displays - 1.Serial Number, 2.Date Made, 3.Purchase Date, 4.Date of last repair (0000 for no repairs), 5.Transfer User Data. To exit this mode you need to switch your phone off then on again

*#94870345123456789# Deactivate the PWM-Mem

**21*number# Turn on "All Calls" diverting to the phone number entered

**61*number# Turn on "No Reply" diverting to the phone number entered

**67*number# Turn on "On Busy" diverting to the phone number entered
12345 This is the default security code
press and hold # Lets you switch between lines

Source
 

SmoothCriminal

New Member
Disciple
Jan 27, 2005
74
2
0
36
www.spicesms.com
MOTOROLA PHONES
Motorola 920
---------------
Press menu and type one of these numbers and press OK:

11 = Status Review
13 = Available Networks
14 = Preferred Networks
22 = Select Keypad Tones
25 = Require SIM Card PIN
26 = Language Selection
32 = Repetitive Timer
33 = Single Alert Timer
34 = Set IN-Call Display
35 = Show Call Timers
36 = Show Call Charges
37 = Call Charge Settings
38 = Reset All Timers
43 = Reset All Timers
45 = Show Last Call
46 = Total For All Calls
47 = Lifetime Timer
51 = Change Unlock Code
52 = Master Reset
53 = Master Clear (Warning!! May result in deleting the Message Editor!!!)
54 = New Security Code
55 = Automatic Lock
63 = Battery Saving Mode

Free call tip

1 Enter the phone number
2 Enter OK
3 Type *#06#
4 Press Button C
5 And finally press the button for power off.

You should now be able to talk without being billed.
The 54# Tip:

Type 1#, 2#........54# on the keypad (when you're not in the menu) to get the phone number used for with this key when speed dialing.

Motorola 930
--------------
Press menu and type one of these numbers and press OK:

11 = Status Review
13 = Available Networks
14 = Preferred Networks
22 = Select Keypad Tones
25 = Require SIM Card PIN
26 = Language Selection
32 = Repetitive Timer
33 = Single Alert Timer
34 = Set IN-Call Display
35 = Show Call Timers
36 = Show Call Charges
37 = Call Charge Settings
38 = Reset All Timers
43 = Reset All Timers
45 = Show Last Call
46 = Total For All Calls
47 = Lifetime Timer
51 = Change Unlock Code
52 = Master Reset
53 = Master Clear (Warning!! May result in deleting the Message Editor!!!)
54 = New Security Code
55 = Automatic Lock
63 = Battery Saving Mode

Free call tip

1 Enter the phone number
2 Enter OK
3 Type *#06#
4 Press Button C
5 And finally press the button for power off.

You should now be able to talk without being billed.
Motorola 930

The 54# Tip:

Type 1#, 2#........54# on the keypad (when you're not in the menu) to get the phone number used for with this key when speed dialing.

Motorola 6200
--------------

(Note: pause means the * key held in until box appears)
To activate RBS type: [pause] [pause] [pause] 1 1 3
[pause] 1 [pause] [ok]
You now have to press the [MENU] and scroll to the 'Eng
Field Options' function with the keys, and enable it.

De-activate RBS

To de-activate RBS type: [pause] [pause] [pause] 1 1 3
[pause] 0 [pause] [ok]
This only works with some versions of software.

These countries has been reported working:

UK (Orange)
AU

What's the use of RBS:

Get Distance From Base Station - Place a call, when it
is answered, press [MENU] until 'Eng Field Option' is
displayed, press [OK], select 'Active Cell', press [OK],
press [MENU] until 'Time Adv xxx' appears, where xxx is
a number. Multiply this number by 550, and the result is
the distance from the RBS (Radio Base Station), in
meters.

Get Signal Quality - press [MENU] until 'Eng Field
Option' is displayed, press [OK], select 'Active Cell',
press [OK], press [MENU] until 'C1' appears. This is the
signal quality. If it becomes negative for longer than 5
seconds, a new cell is selected.

Pin Outs

Numbered left to right, keypad up, battery down

1. Audio Ground
2. V+
3. True data (TD) (input)
4. Downlink - Complimentary data (CD) (input)
5. Uplink - Return data (RD) (output)
6. GND
7. Audio Out - on/off
8. Audio In
9. Manual Test - ???
10. Battery Feedback
11. Antenna connector
Motorola 7500
-------------

(Note: pause means the * key held in until box appears)
To activate RBS type: [pause] [pause] [pause] 1 1 3
[pause] 1 [pause] [ok]
You now have to press the [MENU] and scroll to the 'Eng
Field Options' function with the keys, and enable it.

De-activate RBS

To de-activate RBS type: [pause] [pause] [pause] 1 1 3
[pause] 0 [pause] [ok]
This only works with some versions of software.

These countries has been reported working:

IT (model: F16 HW: 5.2 SW: 2.1)
What's the use of RBS:

Get Distance From Base Station - Place a call, when it
is answered, press [MENU] until 'Eng Field Option' is
displayed, press [OK], select 'Active Cell', press [OK],
press [MENU] until 'Time Adv xxx' appears, where xxx is
a number. Multiply this number by 550, and the result is
the distance from the RBS (Radio Base Station), in
meters.

Get Signal Quality - press [MENU] until 'Eng Field
Option' is displayed, press [OK], select 'Active Cell',
press [OK], press [MENU] until 'C1' appears. This is the
signal quality. If it becomes negative for longer than 5
seconds, a new cell is selected.

Pin Outs
Numbered right to left, keypad up, battery down looking

1. Gnd
2. Pos
3. True data (TD) (input)
4. Complimentary data (CD) (input)
5. Return data (RD) (output)
6. Audio gnd
7. Audio out
8. Audioin
Motorola 8200
--------------

(Note: pause means the * key held in until box appears)
To activate RBS type: [pause] [pause] [pause] 1 1 3
[pause] 1 [pause] [ok]
You now have to press the [MENU] and scroll to the 'Eng
Field Options' function with the keys, and enable it.

De-activate RBS

To de-activate RBS type: [pause] [pause] [pause] 1 1 3
[pause] 0 [pause] [ok]
This only works with some versions of software.

These countries has been reported working:

ES, AU, NL, BE
What's the use of RBS:

Get Distance From Base Station - Place a call, when it
is answered, press [MENU] until 'Eng Field Option' is
displayed, press [OK], select 'Active Cell', press [OK],
press [MENU] until 'Time Adv xxx' appears, where xxx is
a number. Multiply this number by 550, and the result is
the distance from the RBS (Radio Base Station), in
meters.

Get Signal Quality - press [MENU] until 'Eng Field
Option' is displayed, press [OK], select 'Active Cell',
press [OK], press [MENU] until 'C1' appears. This is the
signal quality. If it becomes negative for longer than 5
seconds, a new cell is selected.

Pin Outs

Numbered right to left, keypad up, battery down looking

1. Audio Ground
2. V+
3. True data (TD) (input)
4. Downlink - Complimentary data (CD) (input)
5. Uplink - Return data (RD) (output)
6. GND
7. Audio Out - on/off
8. Audio In
9. Manual Test - ???
10. Battery Feedback
11. Antenna connector

Motorola 8400
-------------

(Note: pause means the * key held in until box appears)
To activate RBS type: [pause] [pause] [pause] 1 1 3
[pause] 1 [pause] [ok]
You now have to press the [MENU] and scroll to the 'Eng
Field Options' function with the keys, and enable it.

De-activate RBS

To de-activate RBS type: [pause] [pause] [pause] 1 1 3
[pause] 0 [pause] [ok]
This only works with some versions of software.

These countries has been reported working:

ES, AU, NL, BE
What's the use of RBS:

Get Distance From Base Station - Place a call, when it
is answered, press [MENU] until 'Eng Field Option' is
displayed, press [OK], select 'Active Cell', press [OK],
press [MENU] until 'Time Adv xxx' appears, where xxx is
a number. Multiply this number by 550, and the result is
the distance from the RBS (Radio Base Station), in
meters.

Get Signal Quality - press [MENU] until 'Eng Field
Option' is displayed, press [OK], select 'Active Cell',
press [OK], press [MENU] until 'C1' appears. This is the
signal quality. If it becomes negative for longer than 5
seconds, a new cell is selected.

Pin Outs

Numbered right to left, keypad up, battery down looking

1. Audio Ground
2. V+
3. True data (TD) (input)
4. Downlink - Complimentary data (CD) (input)
5. Uplink - Return data (RD) (output)
6. GND
7. Audio Out - on/off
8. Audio In
9. Manual Test - ???
10. Battery Feedback
11. Antenna connector

Motorola 8700
--------------

*#06# for checking the IMEI (International Mobile Equipment Identity)

Activate RBS

(Note: pause means the * key held in until box appears)
To activate RBS type: [pause] [pause] [pause] 1 1 3
[pause] 1 [pause] [ok]
You now have to press the [MENU] and scroll to the 'Eng
Field Options' function with the keys, and enable it.

De-activate RBS

To de-activate RBS type: [pause] [pause] [pause] 1 1 3
[pause] 0 [pause] [ok]
This only works with some versions of software.

These countries has been reported working:

AU, IT, SG, DE, ES, ZA

What's the use of RBS:

Get Distance From Base Station - Place a call, when it
is answered, press [MENU] until 'Eng Field Option' is
displayed, press [OK], select 'Active Cell', press [OK],
press [MENU] until 'Time Adv xxx' appears, where xxx is
a number. Multiply this number by 550, and the result is
the distance from the RBS (Radio Base Station), in
meters.

Get Signal Quality - press [MENU] until 'Eng Field
Option' is displayed, press [OK], select 'Active Cell',
press [OK], press [MENU] until 'C1' appears. This is the
signal quality. If it becomes negative for longer than 5
seconds, a new cell is selected.

Motorola CD 160
---------------

Press menu and type one of these numbers and press OK:

11 = Status Review
13 = Available Networks
14 = Preferred Networks
22 = Select Keypad Tones
25 = Require SIM Card PIN
26 = Language Selection
32 = Repetitive Timer
33 = Single Alert Timer
34 = Set IN-Call Display
35 = Show Call Timers
36 = Show Call Charges
37 = Call Charge Settings
38 = Reset All Timers
43 = Reset All Timers
45 = Show Last Call
46 = Total For All Calls
47 = Lifetime Timer
51 = Change Unlock Code
52 = Master Reset
53 = Master Clear (Warning!! May result in deleting the Message Editor!!!)
54 = New Security Code
55 = Automatic Lock
63 = Battery Saving Mode

Free call tip

1 Enter the phone number
2 Enter OK
3 Type *#06#
4 Press Button C
5 And finally press the button for power off.

You should now be able to talk without being billed.

Motorola CD 520
----------------

Press menu and type one of these numbers and press OK:

11 = Status Review
13 = Available Networks
14 = Preferred Networks
22 = Select Keypad Tones
25 = Require SIM Card PIN
26 = Language Selection
32 = Repetitive Timer
33 = Single Alert Timer
34 = Set IN-Call Display
35 = Show Call Timers
36 = Show Call Charges
37 = Call Charge Settings
38 = Reset All Timers
43 = Reset All Timers
45 = Show Last Call
46 = Total For All Calls
47 = Lifetime Timer
51 = Change Unlock Code
52 = Master Reset
53 = Master Clear (Warning!! May result in deleting the Message Editor!!!)
54 = New Security Code
55 = Automatic Lock
63 = Battery Saving Mode

Free call tip

1 Enter the phone number
2 Enter OK
3 Type *#06#
4 Press Button C
5 And finally press the button for power off.

You should now be able to talk without being billed.

Motorola d460
--------------

#06# for checking the IMEI (International Mobile Equipment Identity)

Activate RBS

(Note: pause means the * key held in until box appears)
To activate RBS type: [pause] [pause] [pause] 1 1 3
[pause] 1 [pause] [ok]
You now have to press the [MENU] and scroll to the 'Eng
Field Options' function with the keys, and enable it.

De-activate RBS

To de-activate RBS type: [pause] [pause] [pause] 1 1 3
[pause] 0 [pause] [ok]
This only works with some versions of software.

What's the use of RBS:

Get Distance From Base Station - Place a call, when it
is answered, press [MENU] until 'Eng Field Option' is
displayed, press [OK], select 'Active Cell', press [OK],
press [MENU] until 'Time Adv xxx' appears, where xxx is
a number. Multiply this number by 550, and the result is
the distance from the RBS (Radio Base Station), in
meters.

Get Signal Quality - press [MENU] until 'Eng Field
Option' is displayed, press [OK], select 'Active Cell',
press [OK], press [MENU] until 'C1' appears. This is the
signal quality. If it becomes negative for longer than 5
seconds, a new cell is selected.

Motorola V3688
---------------

#06# for checking the IMEI (International Mobile Equipment Identity)

Enhanced Full Rate Codec (EFR):

To Enable EFR press [][][] 119 [] 1 [] OK.
To Disable EFR press [][][] 119 [] 0 [] OK

NOTE: Nothing appears on Screen.
 

SmoothCriminal

New Member
Disciple
Jan 27, 2005
74
2
0
36
www.spicesms.com
PHILLIPS SECRET CODES

Philips DIGA phones:

Blocking list *#3333*#
Time connected *#2558*#
Flags,something *#3377*#
Security code *#7489*#

Philips FIZZ phones:

IMEI code *#06#
SW info *#8377*#
Security code *#1234*#
Philips SPARK phones:

IMEI: *#06#

Philips GENIE phones:

*#06# IMEI number
*#2254*# Status register: C, BS, RR, MMI, CREAT.
*#2255*# activate and deactivate the "DEBUG CALL"-Mode; when activated, make a call to a busy line an the phone will display some hex-codes on the display
*#2558*# the time in days,hours and minutes you are connected to the net
*#2562*# not clear; the phone reconnects to the net
*#2565*# not clear; warmstart
*#3333*# (NO) BLOCKING - list (15 items)
*#2377*# "BEER": not clear, the phone waits a random time and reconnects to the net
*#3377*# Init, Flags, SIM LCK
*#3353*# resets the (NO) BLOCKING - list
*#7378*# Name, Length, SIM phase
*#7489*# SECURITY CODE
*#7693*# activate and deactivate the SLEEP MODE (when deactivated the battery will go down!)
*#7787*# SPURIOUS INTERRUPT
*#7948*# SWITCH OFF
*#8463*# Some information about the SLEEP MODE: Wake, Sleep Req., Sleep
 
M

MysticYogi

Guest
Nokia codes/functions

*3370#
This Nokia code activates Enhanced Full Rate Codec (EFR) - Your Nokia cell phone uses the best sound quality but talk time is reduced my approx. 5%

#3370#
Deactivate Enhanced Full Rate Codec (EFR)

*#4720#
Activate Half Rate Codec - Your phone uses a lower quality sound but you should gain approx 30% more Talk Time

*#4720#
With this Nokia code you can deactivate the Half Rate Codec

*#0000#
Displays your phones software version, 1st Line : Software Version, 2nd Line : Software Release Date, 3rd Line : Compression Type

*#9999#
Phones software version if *#0000# does not work

*#06#
For checking the International Mobile Equipment Identity (IMEI Number)

#pw+1234567890+1#
Provider Lock Status. (use the "*" button to obtain the "p,w" and "+" symbols)

#pw+1234567890+2#
Network Lock Status. (use the "*" button to obtain the "p,w" and "+" symbols)

#pw+1234567890+3#
Country Lock Status. (use the "*" button to obtain the "p,w" and "+" symbols)

#pw+1234567890+4#
SIM Card Lock Status. (use the "*" button to obtain the "p,w" and "+" symbols)

*#147#
This lets you know who called you last (Only vodofone)

*#1471#
Last call (Only vodofone)

*#21#
This phone code allows you to check the number that "All Calls" are diverted to

*#2640#
Displays phone security code in use

*#30#
Lets you see the private number

*#43#
Allows you to check the "Call Waiting" status of your cell phone.

*#61#
Allows you to check the number that "On No Reply" calls are diverted to

*#62#
Allows you to check the number that "Divert If Unreachable (no service)" calls are diverted to

*#67#
Allows you to check the number that "On Busy Calls" are diverted to

*#67705646#
Phone code that removes operator logo on 3310 & 3330

*#73#
Reset phone timers and game scores

*#746025625#
Displays the SIM Clock status, if your phone supports this power saving feature "SIM Clock Stop Allowed", it means you will get the best standby time possible

*#7760#
Manufactures code

*#7780#
Restore factory settings

*#8110#
Software version for the nokia 8110

*#92702689#
Displays - 1.Serial Number, 2.Date Made, 3.Purchase Date, 4.Date of last repair (0000 for no repairs), 5.Transfer User Data. To exit this mode you need to switch your phone off then on again

*#94870345123456789#
Deactivate the PWM-Mem

**21*number#
Turn on "All Calls" diverting to the phone number entered

**61*number#
Turn on "No Reply" diverting to the phone number entered

**67*number#
Turn on "On Busy" diverting to the phone number entered

12345
This is the default security code

press and hold #
Lets you switch between lines
Hehe ! They might have really useful for all Nokia Freaks !! Have Phun !

Thanks to another forum, where i took this stuff from (iNet)