OC & Modding Post your overclocks !

^^ pretty decent overclock stormy! what cpu core voltage (i see 1.36V in cpuz, so it must be atleast 1.4-1.41V) and mem voltage are you using?
 
rPOk said:
^^ pretty decent overclock stormy! what cpu core voltage (i see 1.36V in cpuz, so it must be atleast 1.4-1.41V) and mem voltage are you using?

everything stock. 1.325 voltage for the 3ghz. ram at 2.1v stock.
ppl are hitting 3500mhz with this same stepping i have with 1.4v.

cpuz never shows the voltage correctly. although i still havent done orthos test yet @ 3ghz.
 
do try orthos man.....1.325V on BIOS i assume....my cpu doesn't pass orthos even at 1.3875V (ram is at 2.1V)....although i can reach 3GHz at 1.325V, i can't make it orthos blend stable for more than 10 mins or so...(maybe its my promos rmemory, since at 2.8GHz, the system is rock solid stable at 1.325V)
 
rPOk said:
do try orthos man.....1.325V on BIOS i assume....my cpu doesn't pass orthos even at 1.3875V (ram is at 2.1V)....although i can reach 3GHz at 1.325V, i can't make it orthos blend stable for more than 10 mins or so...(maybe its my promos rmemory, since at 2.8GHz, the system is rock solid stable at 1.325V)

will surely try it out when i get some free time to tes the pc.
what are the temps with ttbt stock fan for u on idle & load @ 2.8ghz
 
nice temps rpok. mine are both around 10deg more. idle & load @ 2.8ghz. seems like my processor needs to be lapped.

you are using the ttbt stock fan right.
 
Udit said:
:O :O :O

how did you do that please tell me :huh:

I get 45C Idle & 60C Load @430x7 with 1.40v :(
Its still a bit cold in the north :eek:hyeah: . See my screenie a few posts before . I am getting 32 deg load (35 deg while running TAT) at 3 GHz (333 x 9) with my E6600 and stock cooler.
 
hehe...am living in noida (decent enough cold here outside...but my room is warm enough for me to feel any difference ;) )
Here's what i've done for my setup:
- applied AS5 ..it was my first experience and most of you would be better than me in applying it
- original ttbt (no lapping done at all) - its the older version (with 1200rpm fan speed & air flowof 55cuft/m) the newer version has a 1200-2000rpm fan speed and air flow of 85cuft/m
- 3x 80mm fans (2 front intake + 1 side intake for g. card)
- 1x 120mm blue led thermatake smart case rear exhaust fan (at 2800rpm, it has 93cuft/m airflow) - maybe this is lowering the temps a lot...
- nothing else - i've never lapped up my heatsink or processor
- even at 1.3875V & 3.0GHz, load temps (after 4 hours of orthos) in TAT are 47C. :clap:
 
Lord Nemesis said:
Its still a bit cold in the north :eek:hyeah: . See my screenie a few posts before . I am getting 32 deg load (35 deg while running TAT) at 3 GHz (333 x 9) with my E6600 and stock cooler.

U just gave me a lot of hope ... :d ..
 


A64 3200+ Orleans - 2010MHz

Corsair XMS2 DDR2-675 - 400MHz @ 4-4-4-10 1T @1.9V

Waiting for Arctic Silver 5(a couple of days) and better cooler(a month) to push the RAM to the limit. Plan to run the CPU @ around 2.4GHz(24x7); hopefully on stock volts.

RAM looks to be capable of a lot more. Stuck with 800 for now cause of stupid stock HSF and thermal paste.

*Waiting for tips from z pros*
 
2400MHz @ 1.45V

960 2.1V 5-5-5-15 1T

10 hrs Prime95 torture test stable.

Temps were a bit high wen I got up in the morning though .. ~52(with prime95) .. But no A/C ... Plus applied the AS5 just last night ... And no rear exhuast/front intake fans .. Only 2 side fans ...
 
:D .. not CPU oc but oc;ing the RAM ...



Damm .. its too hot for me to push further ... will try later .. 825 at 5-5-5-15 seems fine enough ... though i'll never need it anyway ... RAM volt. was set to Auto :p ...
 
So here it starts. Brisbane ocing on X2 3600+ and cheapo Ramos DDR2 533 ram.
Motherboard :Jetway M2A692-GDG
Stock speed : 1900Mhz
Oced Speeds : 2618Mhz
Vcore : 1.31v
Ram : 748Mhz
vDimm: default 1.95
NB voltage : 1.3
Screenshot after 4 hours of starting boinc at above normal priority.
Room Temp : 25.5C
Cooler : STOCK HSF


Just getting warmed up. ;)
 
Back
Top