Graphic Cards Cleaning up an old R9 270 Graphics card!

SunnyBoi

Branch Manager
Staff member
Patron
So I chanced upon this Sapphire R9 270X Dual-X OC from a fellow member @soulweaver here on TE. Due to logistics and laziness of my friend who picked up the card from him and was too lazy to send it to me, it was a long 6 week wait and I finally got it yesterday!

Here is the sale thread : https://techenclave.com/threads/sapphire-r9-270x.198195/

Just looking at the pictures I could see the card was pretty dirty and being me, I'd have a lot of fun giving it a good clean!

To recap, here's how the card looked

QVfqSYO.jpg


RqBBmAK.jpg


71d0zH0.jpg


There is some dirt between the components on the back of the PCB, the fans may look clean but they are filthy underneath, The heatsink had a fair amount of dirt between the fins too.

Lets get cracking!

First off was the IO plate. It had become very dull. All it needed was some metal polish to bring it back to life. Here are some 50/50 shots

HtZnsgQ.jpg


VsDBhSM.jpg


Very soon, both sides of the IO plate were cleaned up

vEbgs6m.jpg


Removed the heatsink, I was surprised to find a separate small heatsink for half the RAM chips. The thermal paste had dried out and it came off crumbling.

Fc53qDO.jpg


I can't resist a good n00d die shot!

ft1BxTL.jpg


Separated the shroud from the heatsink, the dirt below the fans and the shroud itself is visible.

DdnJc2v.jpg


Took out the fans, gave the blades a good brush and it got out most of the dirt. Wiped the blades then with IPA to get them totally clean. I dusted off the shroud, sprayed it with some soap and gave it a good scrub with a paintbrush to get every last bit of dirt out

The heatsink itself, well it had a fair amount of dirt in it but it would be quite intensive workout for my hands to get them all clean. It looked like the fins had corrosion on them, which isn't uncommon for a 7 year old graphics card. The alternate was to chuck the whole thing in my ultrasonic cleaner! It will make sure every last bit of dirt comes out, even from places a brush can't reach!

9uxnXg9.jpg


10 minutes with soap water at 65*, here's the end result!

r9JiclC.jpg


It may not look too different but it is CLEAN! The corrosion I talked about? That is just solder on the fins! Phew one less thing to worry about!

The PCB was given a dry dusting first, then cleaned again with a brush and IPA. Majority of the dust came off with the dry stage, the IPA clean just makes the PCB look better.

Every part has now been cleaned, time for assembly!

v3zrgGQ.jpg


Looking at the heatsink, it had a copper base and so I decided the thermal interface for the die is going to be liquid metal. LM needs an ultra clean surface on copper with zero oxidation to stick properly. The copper base was cleaned up as well as the heatpipes. Gave the heatpipes a polish too! This is the true color of pure copper!

k2GCZ3z.jpg


The screws holding the heatsink on the PCB had rusted badly. They needed a spruce up. Demel with a wool buffing attachment and metal polish did quick work of the rust and the screws are now SHINY! Here's a 50/50 - the difference is AMAZING.

2zNlqJo.jpg


All 4 are cleaned up!

ZKgYMkf.jpg


The DVI ports, shroud and HDMI port were given a spruce up, can even see the reflecion on HDMI port! IO plate was assembled, die and aluminium surrounding the copper baseplate were given a thick coating of nail polish and left to dry.

T31euBQ.jpg


30 minutes later, time for liquid metal! A bit too much came out of the syringe but hopefully there should be no problems. Worst case scenario, the area around the die has been insulated so let's see.

sZUsKGw.jpg


So here we are at the end! It will be a while before I put the card to use, here are the finished pics!

0AJ1Ukj.jpg


JwedsuF.jpg


kkW2HfJ.jpg
 
Now that is some cleaning a 7 year old card deserves.
I so want to clean and re-paste a 8 month old Gigabyte GPU. But avoiding warranty is stopping me from doing that.

I also did cleaning and re-pasting of an old RX 570, which brought down the temps by 8 degrees.

@SunnyBoi Would love to see before and after temps on full load on this LM pasted GPU of yours.
 
@SunnyBoi Would love to see before and after temps on full load on this LM pasted GPU of yours.
I haven't yet powered on/used the GPU :grimacing: anyway the most load this graphics card will have is plaing solitaire or minesweeper, temperatures are not a concern but it feels good to have a card that is as clean as it can get!
 
D-Day is here! My 6800 series graphics card is replaced with a R9 :tearsofjoy:

Uid3hqR.jpg


Snug in its new home

bUlyo5A.jpg


@SunnyBoi Would love to see before and after temps on full load on this LM pasted GPU of yours.
I ran furmark for about 6 minutes, temps peaked and stayed between 74-75*. Fans werent too loud either, Its a win!

8mB502D.jpg


@SunnyBoi no blaming me if the card doesn't work now... I already bought land with the money you sent. If you want refunds, I can send you a few fistfuls of soil... :p
The card is certified to be running and kicking ass :cool:
 
That copper looks pretty neat for something that's years old. I think it may have some coating. The raw stuff tarnishes ready in my experience very quickly ( from my school days experience with copper coins ). Hopefully they can be laquerered or something?
 
That copper looks pretty neat for something that's years old. I think it may have some coating.
Orange copper is already oxidised! Raw copper looks rose gold like in the later pictures. Since its built up a layer of oxide, it wont rust anymore

I just used a light acid to remove the oxidation and some metal polish to make the heatpipes shine!
 
Back
Top