vijaysurendran
Disciple
hey guys
Need your help from any experts out here.
heres my config
3600 windsor proccy (90nm,256X2 L2) thermalright ultima 90
DFI 790FX M2RS
4 x 1 GB transcend jetram ddr2 800 JM800QLJ-1G,5-5-5-18-23-1.8v
corsair 620 HX
if i just go bumping up the FSB i get to
240 before system becomes unstable
2.4Ghz x2
HT=1200MHZ x2
at 1.37 volts .
memory>= 480 MHZ x2(4 x 1 GB transcend jetram ddr2 800 JM800QLJ-1G,5-5-5-18-23-1.8v)
At the above speeds the system runs stable 24x7
Recently i wanted to see what how much could i push the FSB
and i made it to 300 ,downed the multiplier to 8 and to my surprise it booted fine .
so this time
300x10x8=2.4 ghz
HT at 1500 MHz:S (read in some forums that athlon x2 runs stable at HT speeds betweek 1200 and 1400 .is it true ?)
And memory somewhere around 496 mhz
I could bump the FSB even till 310 :hap2: .
Now when i try to raise the multiplier to 8.5 the system will not POST
So i try to bring down my memory frequency to 667MHZ in bios
but still the system would not post.Tried 533 MHZ -no post ,400MHZ no post ( even tried setting mem timings manually bumped up the memory voltage to 2.2 weak drivers mode etc etc ) still the system refuses to post .
did a bit of research on the net found out someone got to 1050 MHZ
after setting timings to 5-6-6-16-25 at 2.2 volts .
tried the same timings system still does not boot at 300 fsb with multiplier 8.5 or 9.
so what do you guys think memory is the weak link or am i missing something here ?
if it is do you guys have any suggestions of any good overclocking freindly memory (2x2gb kits)?
thnx in advance for any help
Need your help from any experts out here.
heres my config
3600 windsor proccy (90nm,256X2 L2) thermalright ultima 90
DFI 790FX M2RS
4 x 1 GB transcend jetram ddr2 800 JM800QLJ-1G,5-5-5-18-23-1.8v
corsair 620 HX
if i just go bumping up the FSB i get to
240 before system becomes unstable
2.4Ghz x2
HT=1200MHZ x2
at 1.37 volts .
memory>= 480 MHZ x2(4 x 1 GB transcend jetram ddr2 800 JM800QLJ-1G,5-5-5-18-23-1.8v)
At the above speeds the system runs stable 24x7
Recently i wanted to see what how much could i push the FSB
and i made it to 300 ,downed the multiplier to 8 and to my surprise it booted fine .
so this time
300x10x8=2.4 ghz
HT at 1500 MHz:S (read in some forums that athlon x2 runs stable at HT speeds betweek 1200 and 1400 .is it true ?)
And memory somewhere around 496 mhz
I could bump the FSB even till 310 :hap2: .
Now when i try to raise the multiplier to 8.5 the system will not POST
So i try to bring down my memory frequency to 667MHZ in bios
but still the system would not post.Tried 533 MHZ -no post ,400MHZ no post ( even tried setting mem timings manually bumped up the memory voltage to 2.2 weak drivers mode etc etc ) still the system refuses to post .
did a bit of research on the net found out someone got to 1050 MHZ
after setting timings to 5-6-6-16-25 at 2.2 volts .
tried the same timings system still does not boot at 300 fsb with multiplier 8.5 or 9.
so what do you guys think memory is the weak link or am i missing something here ?
if it is do you guys have any suggestions of any good overclocking freindly memory (2x2gb kits)?
thnx in advance for any help