Others 3D Printing Service

[GeeBee007]

@GeeBee007 can you share the file with me? i want to print it and see what the fit seems like. my printer generally has a tolerance of 0.2mm.

If you want then yes why not...Check DM

 

[slippery]

Now finally I dont understand what this guy keeps blabbering about layer lines.
here is a pic of both.
View attachment 241398
Lastly little dissappointed that Crazzy_eddy believed that a somewhat good repped guy on TE would scam for mere 235rs.
Its ok he has to listen to both sides but i mean at the end Does it make sense?
If i was ever a scammer I would have never reached so many successfull trades in TE without a single negative feedback.
If you still want in-depth analysis...I can make side by side comparison between STLs clearing everything but hoping the above would be enough as this just doesnt feel worth for me spending money and wasting time in addition to all this hassle.. @Crazy_Eddy Lemme know what you decide.

I wish you had sent this image of both boxes when I requested on Monday. I didn't publicly accuse you of scamming nor did I outright refuse refund/replacement until you didn't send the picture of both boxes together.

I'll refund you the full cost of the order as well as send you a replacement if you're open to it.

For what it's worth, I apologize for the inconvience. As for why I was so felt so confident about my own assessment, it's a combination of things. Needless to say, you requesting a new iteration rather than a replacement played a part.

Needless to say, this has all been a tiring adventure, just as much as me, I admit, as it must've been for you.

Maybe you'll agree to it, maybe you won't -- but money was never part of the equation or motivation.

 

[arup]

@slippery , I may have a noob question, but is there anyway to get rid of those micro lines appearing in 3d prints?
Maybe if the sides are flat like this geebee's model, is there possibility that you heat the bed and flip all flat sides on that like we flip rotis in hot tawa and that melts the lines and make a smooth finish ...

 

[slippery]

@slippery , I may have a noob question, but is there anyway to get rid of those micro lines appearing in 3d prints?
Maybe if the sides are flat like this geebee's model, is there possibility that you heat the bed and flip all flat sides on that like we flip rotis in hot tawa and that melts the lines and make a smooth finish ...

That's a funny visual so thank you. No, you can't flip it like a hot tava.

The layer lines appear because the printer is literally laying down lines of filament. We can change layer height to the minimum to improve the look.

But layer lines are a physical limitation of FDM prints and ideally, you want to use resin printing to get the closest look to molded plastic, without the obvious layer lines.

The layer lines in resin printing will be MUCH, MUCH smaller than FDM and hence much much less visible.

 

[arup]

That's a funny visual so thank you. No, you can't flip it like a hot tava.

I don't know how this horrible idea came to my mind. I has a 3d printed toy nearby, and out of curiosity I thought I'll heat it up a bit and flaten the lines with a steel ruler. Heated it up using hot air gun only to find that the 3d printed toy (which was very hard ) became like rubber and deforming very easily.. who knows it's petg,pla, or what but it definitely don't behave like normal PVC plastic.

 

[GeeBee007]

Edit:
Hmm... Wrote some harsh things in this same message but guess everyones out here struggling to live , learn and enjoy life.
So I guess its ok, you did what you did.
But had a little heartbreak of those reseller accusations
But as long as I know what the truth is its fine.
Sry from my side as well for acting little harsh.
Hope you learned valuable lessons from this incident and try to do better or else all my time spent here would be for nothing.
Would love to work with you again with more trust then before hopefully.
Peace out.

PS - With this final outcome feeling like Thorfinn from Vinland saga.

 

[slippery]

NEW PRINTER INBOUND:

Hello everyone, the original post states that I have a Bambu A1 Mini with a 180x180x180 mm print bed. I have ordered a Bambu A1 with a bed size of 256x256x256 mm. This means I'll be able to print much bigger prints for you all.

I couldn't edit the original post (even before the migration announcement) so let me know if you guys think I should make a new post with better formatting and clearer information about filaments, pricing, and FAQs. Speaking of filaments...

New filaments in stock:

PLA Matte
- Red
- Blue
- Bubblegum Pink

PLA
- White
- Black
- Light Pink/Beige
- Salmon Pink
- Teal
- Olive/Army Green
- Dark Grey
- Light Grey

PETG
- Black
- White
- Light Grey

 

[Tobikage]

so let me know if you guys think I should make a new post

+1

New thread post migration with better structured info like you mentioned.

Examples of delivered product, material cost , base fee etc and other costs involved considering they are not in the OP here and on Page 3

*Mention damage clause* particularly in the OP.

 

[manohar5321]

New Post please with clear details on pricing, delivery, quality, colors and materials would be good idea. Also add a link back to this post so that people can refer to for more details and printed models from other members

 

[cellar_door]

Got some pretty neat stuff printed. Thanks man.

1 A headphone hanger/cord manager that goes on the back of my monitor.
2 Case for my Miyoo mini plus.
3 Phone holder that goes on my smaller monitor (will post pics once I mount that).