My modem recently got rest to factory settings!
Now i am unable to connect to the internet after doing initial setup. Calling some gurus to help me please!
**************************
DEVICE INFO
**************************
LAN
--------------------------------------------------------------------------------
IP Address : 192.168.1.1
Subnet Mask : 255.255.255.0
DHCP Server : Enabled
WAN
--------------------------------------------------------------------------------
Virtual Circuit : PVC0
Status : Not Connected
Connection Type : PPPoE
IP Address : 0.0.0.0
Subnet Mask : 0.0.0.0
Default Gateway : Node1
DNS Server : 0.0.0.0
ADSL
--------------------------------------------------------------------------------
ADSL Firmware Version : FwVer:3.5.10.0_A_TC3084 HwVer:T14.F7_1.0
Line State : Showtime
Modulation : G.DMT
Annex Mode : ANNEX_A
--------------------------------------------------------------------------------
Downstream Upstream
SNR Margin : 39.5 30.0 db
Line Attenuation : 22.0 8.0 db
Data Rate : 2048 256 kbps
************************************
INTERFACE SETUP
************************************
ATM VC
Virtual Circuit : PVC0
Status : Activated
VPI : 0 (range: 0~255)
VCI : 35 (range: 1~65535)
QoS
--------------------------------------------------------------------------------
ATM QoS : UBR
PCR : 0 cells/second
SCR : cells/second
MBS : cells
Encapsulation
--------------------------------------------------------------------------------
ISP :
Dynamic IP Address
Static IP Address
# PPPoA/PPPoE <--- Selected
Bridge Mode
PPPoE/PPPoA
--------------------------------------------------------------------------------
Username : <user id given>
Password : <password given>
Encapsulation : PPPoE LLC
Bridge Interface : Activated
Connection Setting
--------------------------------------------------------------------------------
Connection : Always On (Recommended) <--- Selected
Connect On-Demand (Close if idle for minutes)
TCP MSS Option : TCP MSS(0:default) 0 bytes
IP Address
--------------------------------------------------------------------------------
Get IP Address : Static # Dynamic <--- Selected
Static IP Address :
IP Subnet Mask :
Gateway :
NAT : Enable
Default Route : # Yes No
TCP MTU Option : TCP MTU(0:default) 1500 bytes
Dynamic Route :RIP2-B Direction Both
Multicast : Disabled
***********************************
LAN SETUP
***********************************
Router Local IP
IP Address : 192.168.1.1
IP Subnet Mask : 255.255.255.0
Dynamic Route : RIP2-B
Multicast : Disabled
DHCP
--------------------------------------------------------------------------------
DHCP : Enabled
DHCP Server
--------------------------------------------------------------------------------
Starting IP Address : 192.168.1.33
IP Pool Count : 32
Lease Time : 259200 seconds (0 sets to default value of 259200)
DNS
--------------------------------------------------------------------------------
DNS Relay : Use Auto Discovered DNS Server Only
Primary DNS Server :
Secondary DNS Server :
***********************************
ADVANCED SETUP
***********************************
Firewall : Enabled
***********************************
NAT
***********************************
Virtual Circuit : PVC0
NAT Status : Activated
Number of IPs : Single
***********************************
QOS
***********************************
QoS : Deactivated
**********************************
ADSL
**********************************
ADSL Mode : Auto Sync-Up
ADSL Type ANNEX A/I/J/L/M
**********************************
DIAGNOSTICS
**********************************
Virtual Circuit: PVC0
>> Testing Ethernet LAN connection ... PASS
>> Testing ADSL Synchronization . PASS
>> Testing ATM OAM segment ping ... PASS
>> Testing ATM OAM end to end ping ... PASS
>> Ping Primary Domain Name Server . SKIPPED
>> Ping Yahoo! ... FAIL
Please help me configure the Modem!!! I am not sure why the VC circuit status for PVC0 shows "Not connected"
S.O.S
Now i am unable to connect to the internet after doing initial setup. Calling some gurus to help me please!
**************************
DEVICE INFO
**************************
LAN
--------------------------------------------------------------------------------
IP Address : 192.168.1.1
Subnet Mask : 255.255.255.0
DHCP Server : Enabled
WAN
--------------------------------------------------------------------------------
Virtual Circuit : PVC0
Status : Not Connected
Connection Type : PPPoE
IP Address : 0.0.0.0
Subnet Mask : 0.0.0.0
Default Gateway : Node1
DNS Server : 0.0.0.0
ADSL
--------------------------------------------------------------------------------
ADSL Firmware Version : FwVer:3.5.10.0_A_TC3084 HwVer:T14.F7_1.0
Line State : Showtime
Modulation : G.DMT
Annex Mode : ANNEX_A
--------------------------------------------------------------------------------
Downstream Upstream
SNR Margin : 39.5 30.0 db
Line Attenuation : 22.0 8.0 db
Data Rate : 2048 256 kbps
************************************
INTERFACE SETUP
************************************
ATM VC
Virtual Circuit : PVC0
Status : Activated
VPI : 0 (range: 0~255)
VCI : 35 (range: 1~65535)
QoS
--------------------------------------------------------------------------------
ATM QoS : UBR
PCR : 0 cells/second
SCR : cells/second
MBS : cells
Encapsulation
--------------------------------------------------------------------------------
ISP :
Dynamic IP Address
Static IP Address
# PPPoA/PPPoE <--- Selected
Bridge Mode
PPPoE/PPPoA
--------------------------------------------------------------------------------
Username : <user id given>
Password : <password given>
Encapsulation : PPPoE LLC
Bridge Interface : Activated
Connection Setting
--------------------------------------------------------------------------------
Connection : Always On (Recommended) <--- Selected
Connect On-Demand (Close if idle for minutes)
TCP MSS Option : TCP MSS(0:default) 0 bytes
IP Address
--------------------------------------------------------------------------------
Get IP Address : Static # Dynamic <--- Selected
Static IP Address :
IP Subnet Mask :
Gateway :
NAT : Enable
Default Route : # Yes No
TCP MTU Option : TCP MTU(0:default) 1500 bytes
Dynamic Route :RIP2-B Direction Both
Multicast : Disabled
***********************************
LAN SETUP
***********************************
Router Local IP
IP Address : 192.168.1.1
IP Subnet Mask : 255.255.255.0
Dynamic Route : RIP2-B
Multicast : Disabled
DHCP
--------------------------------------------------------------------------------
DHCP : Enabled
DHCP Server
--------------------------------------------------------------------------------
Starting IP Address : 192.168.1.33
IP Pool Count : 32
Lease Time : 259200 seconds (0 sets to default value of 259200)
DNS
--------------------------------------------------------------------------------
DNS Relay : Use Auto Discovered DNS Server Only
Primary DNS Server :
Secondary DNS Server :
***********************************
ADVANCED SETUP
***********************************
Firewall : Enabled
***********************************
NAT
***********************************
Virtual Circuit : PVC0
NAT Status : Activated
Number of IPs : Single
***********************************
QOS
***********************************
QoS : Deactivated
**********************************
ADSL
**********************************
ADSL Mode : Auto Sync-Up
ADSL Type ANNEX A/I/J/L/M
**********************************
DIAGNOSTICS
**********************************
Virtual Circuit: PVC0
>> Testing Ethernet LAN connection ... PASS
>> Testing ADSL Synchronization . PASS
>> Testing ATM OAM segment ping ... PASS
>> Testing ATM OAM end to end ping ... PASS
>> Ping Primary Domain Name Server . SKIPPED
>> Ping Yahoo! ... FAIL
Please help me configure the Modem!!! I am not sure why the VC circuit status for PVC0 shows "Not connected"
S.O.S