VSOL V2802RH, ISP Requirements and resources

[d5aqoep]

These things are needed for most people

Jio

1. GPON SN cloning
2. VLAN ID mostly 1015
3. MAC ID cloning (printed on the back of JFHG to be cloned in your router if VSOL is in bridge mode.)
4. Router should be set to DHCP or Automatic mode. No PPPoE

Tata Play Fiber

1. GPON SN cloning
2. PLOAM cloning which is 0123456789
3. HW Version cloning. (It’s mentioned on Nokia router’s web UI status page)
4. VLAN ID (Needs to be discovered after cloning everything)
5. PPPoE Credentials

Airtel

1. GPON SN cloning
2. HW Version cloning. (It’s mentioned on Nokia router’s Web UI status page) This is only required if you are unable to get VLAN using above command and your OLT is ALCL or Tejas. Otherwise it’s not needed.
3. VLAN ID usually 100 (But it needs to be discovered after cloning everything if you are on ALCL OLT)
4. PPPoE Credentials or IPoE Credentials

Microscan

1. GPON SN
2. VLAN usually 744
3. PPPoE Credentials
4. MAC Clone. Or call their CC to reset MAC binding and let it use your router’s real MAC ID.

One Broadband (Oneott Intertainment)

1. GPON SN
2. VLAN
3. PPPoE Credentials
4. MAC Clone. Or call their CC to reset MAC binding and let it use your router’s real MAC ID.

GIGA Net Broadband OPC Pvt Ltd

1. GPON SN
2. VLAN
3. PPPoE Credentials
4. MAC Clone. Or call their CC to reset MAC binding and let it use your router’s real MAC ID.

BSNL (EPON)

1. Get VSOL to register on BSNL’s EPON OLT (Coordinate with installer or NOC guy)
2. Ask BSNL for TR069 Details which need to be inserted in VSOL’s CWMP section
3. PPPoE Credentials

Excitel (EPON)

1. GPON SN
2. MAC OUI or Clone MAC address
3. PPPoE Credentials

Useful VSOL commands for Telnet: (You have to enable telnet first)

Follow the below guide to enable telnet (Chinese → English translate in browser)

https://post.smzdm.com/p/akkod859/

Vendor: Nokia (Mostly TataPlay Fiber and sometimes Airtel too)
Vendor ID: ALCL

Vendor: Huawei
Vendor ID: HWTC

Vendor: ZTE
Vendor ID: ZTEG

Vendor Sercomm (Mostly Jio)
Vendor ID: SCOM

GPON SN: (For Jio, it’s not Printed at the back like everybody else. So follow Anmol Bharadwaj’s guide below to get it.)

VSOL V2802RH or Photon PTF2282 telnet/ssh commands

Determine which of the following commands are required based on your ISP requirements mentioned above.
flash set GPON_SN ALCLxxxxxxxx
flash set GPON_PLOAM_PASSWD 0
cfgmib set OMCI_SW_VER1 XXXXXX
cfgmib set OMCI_SW_VER2 XXXXXX
flash set PON_VENDOR_ID XXXX
flash set HW_HWVER XXXXX

Below are the commands for EPON based connections if required for ISPs like BSNL and Excitel:

flash set ELAN_MAC_ADDR XXXX
flash set OUI XXXX

To get VLAN IDs after O5 state:
omcicli mib get 84

To get OLT Vendor IDs in HEX state:
omcicli mib get 131

Disable Login Captcha
flash set VALIDATE_CODE_SWITCH 0

Pass these 2 command at the end to save and reboot ONU
cfgmib save
restart

Use browser translator and follow guides here:

Tutorial como substituir modem fibra FTTH do provedor pelo modem VSOL V2802RH...

To obtain Jio Fiber Home Gateway’s GPON SN, follow this guide:

Bypassing Jio Fiber Router/ONT -Guide

Compatible Routers/ONU that are found to be working perfectly fine with JioFiber TP Link G3 V1 VSOL V280RH / PTF 8132 [2.5GB ONUs] ODI/HSGQ SFP STICK 2.5 Gb JIO uses GPON authentication and for it to work Its serial number needs to be authenticated at the ONU . also it uses DHCP and not PPPoE unlike airtel so you dont need any username or password for it Obtain the Jio Router’s WAN MAC Address Locate the WAN MAC address on the back sticker of your Jio router. Get the 4-Character Rout…

I request people to keep different IP ranges of VSOL and your Router.

If your Router is 192.168.1.1 then change VSOL’s IP to 192.168.0.1

[rocking]

Thank you so much for putting it in short yet informative, detailed guide to get started.

[d5aqoep]

For those with Debian based Routers like Ubiquiti, you can access VSOL if it is in bridge mode as long as it is on different IP range compared to Ubiquiti

Eg. Ubiquiti Gateway Router is on 192.168.1.1, then VSOL must be on 192.168.0.1 or 192.168.2.1 or 10.100.1.1, etc as per your choice.

Follow this video to know your ETH Port number

Easy AT&T BGW320 Gateway Bypass with UniFi UDM Pro Max via the WAS-110 SFP ONT on a stick from 8311

These are the SSH commands for Ubiquiti Gateway Router which will enable temp access to VSOL. Modify IP address and 0 of eth0 as per your device.

ip addr add dev eth0 local 192.168.0.2/24
iptables -t nat -A POSTROUTING -o eth0 -d 192.168.0.0/24 -j SNAT --to 192.168.0.2

Then you can access VSOL directly in browser using 192.168.0.1

[DrFreeman]

This should work for OpenWRT too

[d5aqoep]

If you have any success story in using V2802RH with an ISP not listed here, do let me know. I will update the main post.