User Guides A guide to port forward Beetel 220BX

Guide to basic Port Forwarding on

BEETEL 220BX ADSL2+ MODEM
Why port forward ?
There are programs that require direct peer to peer connection for maximum efficiency of the connection…these are peer-to-peer applications…:p like kazaa,bittorrent clients(azureus,utorrent,bitcomet)

What are these ports?
Ports are like ‘logical’ doors…thru which a data is supposed to come into.
Think of like a short cut to your Girlfriends place…u first try to go through the shortest route….(the configured port of the software)..if the route/port is unavailable u try all type of direction & go by some other route/port. This is the simplest explanation that I could think of.:p

What happens when port is forwarded?
When we port forward , a route to our computer in made available freely…the advantage the data can be received by your machine very quickly & hence the efficiency increases.:clap:
(both upload & download speeds are affected )

How to port forward ?
Airtels’ modem 220bx is very simple to port forward…the simplest I’ve come across.
It can be done from telent or thru a browser…assuming u find browser more convenient…I’ve provided screenshots for the same along with each steps.
------------------------------------------------------------------------
Procedure 1 : Browser Interface
------------------------------------------------------------------------
NOTE: The new firmwares seem to hide the NAT option in browser interface & you may get the interface like below,
Image by gulve

dont worry...just follow the Procedure 2 , where u can do the job through TELNET...the keywords & config all are same..only inter


To check whether a ports is open ::D
Go to
Code:
[SIZE="2"]https://www.grc.com/x/portprobe=60215[/SIZE]
Where 60215 is the port u want to check.

If the result u get is ‘stealth’ , then are ports are not forwarded ( the data should come from long road)

If the result is ‘Closed’, then the port is forwarded but not being used.

If the result is ‘Open’, the port is forwarded & is used
  • you must be aware of
    http://192.168.1.1 , this provides basic options for advanced
    options
    u are to go to
    http://192.168.1.1/main.html
    Now go to the 192.168.1.1/main.html
    (password by default is admin,admin or admin,password or admin,123456…if this fails call your
    CC)
  • After the page opens
    Click on Advanced Setup-->NAT-->Virtual Servers
  • You are supposed to get the image as below

    click on custom server give whatever name u want
    Then click on the server ip address…by default if u are using the modem on a single machine the ip address would be 192.168.1.2
    So enter that .
    (u can verify by , command-->ipconfig-->ipaddress . this ipaddress should be entered here)
  • Suppose we want to open up port 5000,5001,5002,5003,5004,5005
    then external port & enter 5000 , external port end  5005


    The internal port start & end would be done automatically.
    (note : u can also open 1 single port by giving external port start & end the same..
    for example…if u want to open port 69999 give the start & end as 69999)
  • Save & reboot the modem
(End of port forwarding using Browser interface)
------------------------------------------------------------------------
Procedure 2 : TELNET Interface
------------------------------------------------------------------------
  • launch cmd & type in
    Code:
    telnet 192.168.1.1
  • give the authentication info of the modem.
    (password by default is admin,admin or admin,123456…if this fails call your CC)
  • you see this screen
    Code:
       Main Menu
    
    1.  ADSL Link State
    2.  LAN
    3.  WAN
    4.  DNS Server
    5.  Route Setup
    6.  NAT
    7.  Firewall
    8.  Quality Of Service
    9.  Management
    10. Passwords
    11. Reset to Default
    12. Save and Reboot
    13. Exit
     ->
    select 6 & press enter.
  • you will get this screen

    Code:
       NAT Menu
    
    1. Virtual Server
    2. DMZ
    3. Exit
    / NAT ->
    Choose 1 & press enter
  • Code:
       Virtual Server Menu
    
    1. Add
    2. Remove
    3. Show
    4. Exit
    / NAT/Virtual Server ->
    Press 1 & press enter
  • Code:
            Virtual Server Add
    
    Note: Hit return at prompt if parameter is not used or to accept default value.
    Press <enter> to use current value
    Press <esc> and <enter> to cancel
    
    Service name ()                             :
    Enter a name for the port forward operation..in this case i give it test_1
  • Code:
    Service name ()                             : test_1
    Protocol [0-tcp&udp,1-tcp,2-udp,3-icmp] (1) :
    Selecting 0 enables you to forwardboth TCP & UDP(recommended)
    choose 1 & press enter
  • Code:
    Service name ()                             : test_1
    Protocol [0-tcp&udp,1-tcp,2-udp,3-icmp] (1) : 1
    External start port ()                      : 56666
    External end port ()                        : 56668
    Internal start port ()                      : 56666
    Internal end port ()                        : 56668
    Internal server IP address ()               : 192.168.1.2

    Enter the code in the above fashion manner. & press enter

    By convention External start port & Internal Start port should be the same .
    External end port & External End port should be the same.

    Internal IP address : This is the IP the modem is assigning to your computer.
    by default if u are using the modem on a single machine the ip address would be 192.168.1.2
    So enter that .
    (u can verify by , command-->ipconfig-->ipaddress . this ipaddress should be entered here)

    Code:
    OK..so how to give about start port no & end port no?
    say for example you want to open the port 60000
    then give
    External start port () : 60000
    External end port () : 60000
    Internal start port () : 60000
    Internal end port () : 60000
    If u want to open a series of ports...say for example 60000 to 60010
    then give
    External start port () : 60000
    External end port () : 60010
    Internal start port () : 60000
    Internal end port () : 60010

    after you enter the detials in above manner
    you will get this message
    Code:
    Hit <enter> to continue

    press enter & you will be taken back to this screen.

    Code:
       Virtual Server Menu
    
    1. Add
    2. Remove
    3. Show
    4. Exit
    / NAT/Virtual Server ->
  • You have successfully port forwarded.
    for removing the opend port follow the same procedure.
    You may see all the ports opened selecting option 3.
    or come out of telnet by choosing option 4.


    snapshot of telnet window showing all the forwarded ports.
------------------------------------------------------------------------
(End of port forwarding using TELNET interface)
That’s it you are done port forwarding , u can check the port u forwarded by the link I have give at the beginning of this guide.

If u have any problems while doing this procedure...drop in a request in this thread..& i'll try to sort it out.:)
 
^ ok..try to do it yourself(if u know what u are doing)..or come back tomorrow..will add forwarding in this telnet to the guide by tomorrow...me going offline for smtime..
 
Guide to basic Port Forwarding on

BEETEL 220BX ADSL2+ MODEM
Why port forward ?
There are programs that require direct peer to peer connection for maximum efficiency of the connection…these are peer-to-peer applications…:p like kazaa,bittorrent clients(azureus,utorrent,bitcomet)

What are these ports?
Ports are like ‘logical’ doors…thru which a data is supposed to come into.
Think of like a short cut to your Girlfriends place…u first try to go through the shortest route….(the configured port of the software)..if the route/port is unavailable u try all type of direction & go by some other route/port. This is the simplest explanation that I could think of.:p

What happens when port is forwarded?
When we port forward , a route to our computer in made available freely…the advantage the data can be received by your machine very quickly & hence the efficiency increases.:clap:
(both upload & download speeds are affected )

How to port forward ?
Airtels’ modem 220bx is very simple to port forward…the simplest I’ve come across.
It can be done from telent or thru a browser…assuming u find browser more convenient…I’ve provided screenshots for the same along with each steps.
------------------------------------------------------------------------
Procedure 1 : Browser Interface
------------------------------------------------------------------------
NOTE: The new firmwares seem to hide the NAT option in browser interface & you may get the interface like below,
Image by gulve

dont worry...just follow the Procedure 2 , where u can do the job through TELNET...the keywords & config all are same..only inter


To check whether a ports is open ::D
Go to
Code:
[SIZE="2"]https://www.grc.com/x/portprobe=60215[/SIZE]
Where 60215 is the port u want to check.

If the result u get is ‘stealth’ , then are ports are not forwarded ( the data should come from long road)

If the result is ‘Closed’, then the port is forwarded but not being used.

If the result is ‘Open’, the port is forwarded & is used
  • you must be aware of
    http://192.168.1.1 , this provides basic options for advanced
    options
    u are to go to
    http://192.168.1.1/main.html
    Now go to the 192.168.1.1/main.html
    (password by default is admin,admin or admin,password or admin,123456…if this fails call your
    CC)
  • After the page opens
    Click on Advanced Setup-->NAT-->Virtual Servers
  • You are supposed to get the image as below

    click on custom server give whatever name u want
    Then click on the server ip address…by default if u are using the modem on a single machine the ip address would be 192.168.1.2
    So enter that .
    (u can verify by , command-->ipconfig-->ipaddress . this ipaddress should be entered here)
  • Suppose we want to open up port 5000,5001,5002,5003,5004,5005
    then external port & enter 5000 , external port end  5005


    The internal port start & end would be done automatically.
    (note : u can also open 1 single port by giving external port start & end the same..
    for example…if u want to open port 69999 give the start & end as 69999)
  • Save & reboot the modem
(End of port forwarding using Browser interface)
------------------------------------------------------------------------
Procedure 2 : TELNET Interface
------------------------------------------------------------------------
  • launch cmd & type in
    Code:
    telnet 192.168.1.1
  • give the authentication info of the modem.
    (password by default is admin,admin or admin,123456…if this fails call your CC)
  • you see this screen
    Code:
       Main Menu
    
    1.  ADSL Link State
    2.  LAN
    3.  WAN
    4.  DNS Server
    5.  Route Setup
    6.  NAT
    7.  Firewall
    8.  Quality Of Service
    9.  Management
    10. Passwords
    11. Reset to Default
    12. Save and Reboot
    13. Exit
     ->
    select 6 & press enter.
  • you will get this screen

    Code:
       NAT Menu
    
    1. Virtual Server
    2. DMZ
    3. Exit
    / NAT ->
    Choose 1 & press enter
  • Code:
       Virtual Server Menu
    
    1. Add
    2. Remove
    3. Show
    4. Exit
    / NAT/Virtual Server ->
    Press 1 & press enter
  • Code:
            Virtual Server Add
    
    Note: Hit return at prompt if parameter is not used or to accept default value.
    Press <enter> to use current value
    Press <esc> and <enter> to cancel
    
    Service name ()                             :
    Enter a name for the port forward operation..in this case i give it test_1
  • Code:
    Service name ()                             : test_1
    Protocol [0-tcp&udp,1-tcp,2-udp,3-icmp] (1) :
    Selecting 0 enables you to forwardboth TCP & UDP(recommended)
    choose 1 & press enter
  • Code:
    Service name ()                             : test_1
    Protocol [0-tcp&udp,1-tcp,2-udp,3-icmp] (1) : 1
    External start port ()                      : 56666
    External end port ()                        : 56668
    Internal start port ()                      : 56666
    Internal end port ()                        : 56668
    Internal server IP address ()               : 192.168.1.2

    Enter the code in the above fashion manner. & press enter

    By convention External start port & Internal Start port should be the same .
    External end port & External End port should be the same.

    Internal IP address : This is the IP the modem is assigning to your computer.
    by default if u are using the modem on a single machine the ip address would be 192.168.1.2
    So enter that .
    (u can verify by , command-->ipconfig-->ipaddress . this ipaddress should be entered here)

    Code:
    OK..so how to give about start port no & end port no?
    say for example you want to open the port 60000
    then give
    External start port () : 60000
    External end port () : 60000
    Internal start port () : 60000
    Internal end port () : 60000
    If u want to open a series of ports...say for example 60000 to 60010
    then give
    External start port () : 60000
    External end port () : 60010
    Internal start port () : 60000
    Internal end port () : 60010

    after you enter the detials in above manner
    you will get this message
    Code:
    Hit <enter> to continue

    press enter & you will be taken back to this screen.

    Code:
       Virtual Server Menu
    
    1. Add
    2. Remove
    3. Show
    4. Exit
    / NAT/Virtual Server ->
  • You have successfully port forwarded.
    for removing the opend port follow the same procedure.
    You may see all the ports opened selecting option 3.
    or come out of telnet by choosing option 4.


    snapshot of telnet window showing all the forwarded ports.
------------------------------------------------------------------------
(End of port forwarding using TELNET interface)
That’s it you are done port forwarding , u can check the port u forwarded by the link I have give at the beginning of this guide.

If u have any problems while doing this procedure...drop in a request in this thread..& i'll try to sort it out.:)
 
is it safe enuf to forward ports???

doesn't it expose our PC's contents to other ppl ?

lol i know no terminologies. i'm a n00b ..

please help
 
^go to the page where you create the ports & delete em..:)

on the corner of the table in the NAT page(Virtual server page) you have options of tickbox...

select all those u want to delete & press "REMOVE".
 
I followed your instructions, but Shields Up still reports any port i try as 'Stealth'. Heres a screenshot of my DSL Router Advanced setup --> NAT --> Virtual Servers page.

my.php


Help!
 
Hey guys,

I turned my Zyxel Prestige 600 router in for a Beetel 220BX. However, i've been having some problems with it. Note:i'm using this modem with a single machine. The Zyxel had no issues with WLM, and didn't need any port forwarding to be set up. However WLM isn't working with the 220BX. The 220BX i received has a new firmware with the ports for popular programs preprogrammed. I enabled these ports but WLM still wouldn't work. I also tried manually opening ports

1863 TCP

6891-6900 TCP

6901 TCP

5190 UDP

however WLM still doesn't seem to work. WLM diagnostics show that the Gateway isn't responding.

I'd appreciate the help guys.

cheers

inzider
 
^you have done the port forwarding in a proper way...to make use of the port..just configure the port to use in a p2p software...then it'll open...

i.e, when a application is making use of that port , the result u shd expect is open . :)
 
I configured uTorrent to use the port. I left uTorrent on all night but when I came in the morning the port was still closed? I checked using Utorrent port checker.

Why?

Also... I don't but I have Norton Antivirus running. Do I need to configure that? If so how?
 
^you dont have to confugure any firewall IMO...but you'll have to configure any firewall installed on the system. .

Arihant.exe said:
<<--- Do he have to or do he not have to :S

OOPS....:no:
i meant this ,
^you dont have to configure any antivirus IMO...but you'll have to configure any firewall installed on the system. .
:rofl:
 
Back
Top